4 Easy and fast way to jump start car

4 Ways To Jump Start Car With A Dead Battery Without Another Car

The Proper Way to Jump Start Cars

When you’re getting ready to jump start cars battery, you should find a set of jumper cables and another vehicle you can use to get a jolt. Once you have this equipment, simply take the following steps to get back on the roads :

  • Take the car with a good battery and park it close to the dead vehicle, so that their hoods are almost touching. Engage both parking brakes and make sure both vehicles are turned off before you go further.
  • Open both hoods and locate each battery. In some cases, the battery might be covered by a plastic hood.
  • Identify the positive (red) and negative (black) terminals on both batteries. If they’re clean and free of corrosion, you’re ready to proceed.
  • Connect the red clamp to the positive terminal on the dead battery if doesn’t work hired a service to jump start cars
  • Uncoil the battery cable and hook up the other red clamp to the positive terminal on the live vehicle.
  • While you’re facing the good battery, connect the black end of the cable to the negative terminal.
  • Going back to the vehicle with the dead battery, connect the last black cable clamp to a flat, unpainted metal surface on the car’s frame.
  • With all the connections in their proper places, start the engine of the working vehicle, and let it run for a few moments. This will pass a charge to the once-dead battery.

More Battery Tips and Tricks

If your jump start doesn’t proceed as planned, then you might be understandably frustrated. Take advantage of these tips to narrow down the range of possible issues and figure out how to get back to your life:

  • Perhaps you try to start the car, but you’re only hearing a clicking sound. In these cases, your battery is probably fine, but your starter may be malfunctioning.
  • If you’re able to get your car’s electrical systems to turn on, but your engine still won’t start, you might be facing an issue with your ignition switch, starter, or fuses. A completely dead battery might also be at fault.
  • If you’re able to jump start the car, but the battery dies again soon after you get on the road. You might be dealing with a weak alternator.

 

If your car battery has died, you may be able to use jumper cables to jump-start car it with the help of some good Samaritan’s vehicle. If you can safely use jumper cables on your vehicle, make sure that the battery on the good Samaritan’s vehicle has at least as much voltage as your own.
 
As long as you hook up the cables properly, it doesn’t matter whether your vehicle has negative ground and the other vehicle has positive ground, or your vehicle has an alternator and the other vehicle has a generator.
 
Most Cars Just got battery low when the cool weather start in the morning, is very recommended to keep checking an batter corrosion or the batter terminals to be in good looking condition to keep the battery safe the most easy way to keep your car healthy and avoid calling a service to jump start car is to keep checking your car battery o replace the battery every two or tree years, Most services to jump start cars start from $50 and up is the regular price to get someone there and help you to jump your car battery
pinterest sharing button
Jump start cars battery now day is more required for any new car, why? now the automatic cars are no like manual transmission cars that you can put it and release the clutch car engine start when the alternator generate power for the sparkplugs, automatic cars required power to jump start car battery
whatsapp sharing button
Jump Start A Car Without Another Car

6 Minutes Read

It is the worst situation when your car stops in the middle of nowhere due to a dead battery and it makes the situation even worst when you don’t have another car or jump leads. You might call your friend for assistance, but it is not good relying on your friends and take their kindness all the time for jump-starting the car.

Therefore, it is very important to know this essential skill of jump start car without another car with a dead battery, including a portable jump starter. In my last article, I have comprehensively explained how you can jump-start a car with another car. But, in this article, we will discuss how to jump-start a car without another car.

In this incredibly amazing and powerful article, you are going to learn the four different ways to jump start car with a dead battery without another car easily and quickly with pictures, including a portable jump starter.

Related • How To Jump Start Cars With Leads By Yourself With 3 Quick Steps | The Best Ever Read |

Table Of Contents
  1. How To Start A Car With A Dead Battery Without Another Car
    • Method 1. How To Jump Start Cars With A Battery Pack
    • Portable Jump Starter/ Battery Booster Pack
    • Step By Step Procedure To Jump Start A Car With Portable Jump Start
      • Step 1. Be Ready
      • Step 2. Make The Connections
      • Step 3. Power The Ignition
      • What To Do After Jump Starting
    • Method 2. How To Jump Start A Car With A Spare Battery
      • Step 1. Get Into Condition
      • Step 2. Tip The Battery Upside Down
      • Step 3. Start The Car
    • Method 3. Bridging Two Batteries Using Tools
      • Step 1. Get Everything Ready
      • Step 2. Link The Connections
      • Step 3. Power The Engine
    • Method 4. Bump/Push Start

 

How To Start A Car With A Dead Battery Without Another Car

Below are the four different ways to quickly jump-start a car without another car.

  1. Jump start  Car With A Portable Jump Start
  2. Tipping The Battery Upside Down
  3. Bridging Two Batteries Using Tools
  4. Bump/Push Start
  5.  

 

Method 1. How To Jump Start Cars With A Battery Pack

Jump starting a car without another car through a battery pack (portable jump starter) is the easy and fast method of jump-starting the car by yourself. All you need is a portable jump starter.

Portable Jump Starter to jump start car / Battery Booster Pack

Portable Jump Starter With Leads
Portable Jump Starter With Leads

A Portable Jump Starter also called “Battery Booster Pack”, “Power Bank”, “Emergency Booster”, “Battery Jumper”, or “Jump Box” is a compact portable battery that provides 12 volts back up power to boost the car’s dead battery for jump-starting.

It is safely used to jump-start the manual and automatic transmission car by yourself without needing another car’s help. There are various types of portable jump starters. The lead-acid and lithium-ion are the common types of jump starters. The lead-acid jump starter is very heavy and bigger but, could start the car a few times before goes down.

Conversely, the newer lithium jump starter is made up of lithium-ion or lithium-polymer, is a pocket-size small and light jump starter that can provide up to more than ten starts when fully charged.

The portable jump starter comes with many features such as an emergency light, USB charger for charging cell phones and tablets, radio, even the built-in compressor to fill your car’s tire in an emergency. The jump starter is rechargeable and can be plugged into a household outlet.

Step By Step Procedure To Jump Start A Car With Portable Jump Start

Below is the step-by-step procedure of jump-starting a car without another car through a portable jump starter by yourself.

Step 1. How to Be Ready to jump start car in the street

Opened Hood

 

Opened Hood
  • First of all, open the hood, locate the battery and remove the battery terminal covers.
  • Identify the negative and positive posts of the battery.
  • Identify the positive and negative leads on the jump starter. Usually, the red lead is considered a positive, and the black lead is considered a negative power source.
  • Set the parking brake.

This is a Danger
Do not smoke near the battery. Make sure the car is away from flammable material.

This is a Danger
Keep the dangling clothes, jewelry, bracelet, face away from the battery.

Step 2. Make The Connections

Making Jump Starter Connections

 

Making Jump Starter Connections
  • Put the positive (red) lead on the battery’s positive post and negative (black) lead on an unpainted clean car frame or engine block (not a moving part).
  • Make sure the jump starter leads are firmly connected.
  • Turn on the jump starter.

This is an Info
You can connect the jump starter negative lead to the car’s dead battery negative terminal, but engineers don’t recommend it. The chances are it could spark and cause a fire.

Step 3. Power The Ignition

Powering The Ignition Switch

 

Powering The Ignition Switch

Now crank the engine for a short time. It should start in the first attempt. If it doesn’t start, then wait for a few minutes to try again.

This is a Tip
You do not need to crank the engine for a long period of time, it could damage the starter motor and also rapidly discharge the portable jump starter.

This is an Info
The portable jump starter does not charge your car’s battery but rather provides the necessary amperage to the starter motor to crank the engine and start it.

What To Do After Jump Starting

After the engine starts, turn off and remove the jump starter. Let the car run for 15-20 minutes to charge the battery.

Remove jump starter leads in reverse order, the way it was connected. First, remove the black lead, then the red one. Recharge the jump starter for 3-4 hours for the next usage.

 

Method 2. How To Jump Start Car With A Spare Battery

(By Tipping The Battery Upside Down)

Jump Starting The Car By Tipping The Battery Upside Down

 

Jump-Starting The Car By Tipping The Battery Upside Down

If you don’t have the jump leads or another car, don’t worry. Here is another quick method through which you can jump-start a car with a dead battery. In this quick method, a boost battery is tipped upside down to a dead battery to start the car.

You only need a powerful spare battery. Try to find a maintenance-free and spill-free battery with a crack-free casing. It is because, in this method, the car is jump-started with the powerful spare battery is flipped upside down to a dead battery, so that the liquid inside the battery does not spill out.

Step By Step Procedure Of Jump Starting The Car By Tipping The Battery Upside Down

Step 1. Get Into Condition

Car-Ignition-Switch

 

Car-Ignition-Switch

Turn the ignition switch to an open position and turn off all the accessories such as radio, roof light, headlights, etc.

Step 2. Tip The Battery Upside Down

Tipping The Battery Upside Down - jump start car with other battery

 

Tipping The Battery Upside Down

Place the tip of the boost battery upside down on the car’s dead battery in such a way that the red terminal of the boost battery becomes properly lined up to the red terminal of the dead battery. Similarly, the black terminal of the boost battery lined up to the black terminal of the dead battery.

Step 3. Start The Car

Beautiful Girl Is Starting The Car- Jump start car easy

 

Beautiful Girl Is Starting The Car

Now you should turn the ignition key to the start position. The car should start. Remove the boost battery from the car and run the car for 15-20 minutes to charge the dead battery

 

Method 3. Bridging Two Batteries Using Tools

Bridging-Two-Batteries-Using-Tools- jump start cars

 

Bridging-Two-Batteries-Using-Tools

You can also jump start cars without another car by bridging two batteries using tools. In this fast method, a spare battery is linked together with a dead battery to boost the power of the dead battery to start the car.

If the tip of the lead-acid battery is turned upside down, the chance is that you can spill out the acid from the battery, which can cause chemical harm to your hand as well as damage the car parts.

In case, you do not have a maintenance-free and spill-free battery to flip upside down, you can use the normal lead-acid battery to bridge with a dead battery by using tools such as a spanner. The best way to jump-start a lead-acid battery is by putting it on the side by side to a dead battery, using tools to bridge the gap between dead and boost battery.

Step By Step Procedure Of Jump Starting The Car By Bridging Two Batteries Using Tools

Step 1. Get Everything Ready

Opened Hood

 

Opened Hood

Park the car in the safe area. Open the hood. Bring the boost battery and put it aside by the dead battery.

Step 2. Link The Connections

Jump Starting The Car By Bridging Two Batteries Using Spanner

 

Jump-Starting The Car By Bridging Two Batteries Using Spanner

Bridge the gap by attaching the spanner or other tools to the red terminals of both boost and dead batteries. Similarly, attach the second spanner or other tools to the black terminals of both boost and dead battery.

This is a Danger
You should hold the spanner firmly to both batteries otherwise it will get hot. A poor holding of the spanner can ignite the gasses produced by the battery.

Step 3. Power The Engine

Now you turn the ignition key to the start position, and the car should start. Let the car run for 15 to 20 minutes to charge the dead battery.

Method 4. Bump/Push Start

bump/push-start

You can also start the car through the bump/push start method without another car by yourself by pushing it backward or forward. A bump/push start is a method of starting the car by pushing or pulling on a traffic-free road or downhill.

In bump starting, the car is made to move while the transmission is engaged to the engine to spin and start it. Below is an amazing and comprehensive guide about bump starting a manual and automatic transmission car by yourself without another car.

whatsapp sharing button

the most easy and safe jump start cars without another car is here check our safety recommendations

To safely jump start cars, follow these steps:

  1. Take out your jumper cables. It’s a good idea to buy a set of jumper cables and keep them in the trunk compartment. If you don’t have jumper cables, you have to find a kind stranger who not only is willing to assist you, but who has jumper cables as well.
  2. Place both vehicles in Park or Neutral and shut off the ignition in both cars. Engage both parking brakes as well.
  3. Attach one of the red clips to the positive terminal of your battery. It has “POS” or “+” on it, or it’s bigger than the negative terminal.
  4. Attach the other red clip to the positive terminal of the other car.
  5. Attach one of the black clips to the negative terminal on the other battery.
  6. Attach the last black clip to an unpainted metal surface on your car that isn’t near the battery. Use one of the metal struts that holds the hood open. The cables should look like this.

For Heavy Duty Jump start for a semi truck jump start you cant used one of the small jump start cars portable you must used heavy duty cables

Semi truck Jump start required a lot power to get the big rig start the fastest way to jump start a heavy duty truck is to having a big cables and another’s heavy duty truck with big batteries on it so the power can pass quick to the semi truck

  • when to call a jump start a cars service?
  • Call when you see in the morning your engine doesn’t do a noise
  • if the engine move strong and no starting that’s no a jump start car service need it
  • You car cant died in the freeway and then said you need a jump start
  • Car has an electric generator that name Alternator he is the one that make sure you can go without battery
Service to jump start a car, jump start car

If you cant get your car started just call the professional service to jump start cars nearby Our towing Company offers the most easies way to jump start a car services nearby in all united states

Another way and the most common way to jump Start cars is here

1

Locate Another Vehicle

two cars side by side with each front hood open

  • In order to jump start car, park another vehicle with a full battery near your car. 
  • To make sure the jumper cables reach, park the second car in front of the one with the dead battery so that both front bumpers are facing each other.
  • If there’s not enough space to park with the front bumpers facing each other, park the other vehicle closely alongside your car so the car batteries are as close together as possible.

Tip: Although both vehicls should be close together, they should not be directly touching each other. 2

Locate the Battery Terminals

a close up of a car battery terminal

  • Take the keys out of the ignition in both vehicles and open the front hoods.
  • Find both batteries and locate the positive and negative terminals on each one.
  • Car batteries have two metal terminals. The positive terminal will be marked with a plus sign (+) and the negative terminal will be marked with a minus sign (-). If there is no symbol indicator, the positive terminal will be connect with a red cable and the negative terminal will be connected with a black cable.
  • When using the jumper cables, always remember that the red clamp connects to the positive (+) terminal and the black clamp connects to the negative (-) terminal.

3

Connect the Jumper Cables

jumper cables connected to a car battery

  • Separate the jumper cables and make sure the ends do not touch each other throughout the jump-start process. 
  • Take one end of the jumper cables and connect the red clamp to metal post on the positive terminal of the dead car battery. Set the corresponding black clamp to the side.
  • Move to the other end of the jumper cables and connect the red clamp to the metal post on the positive terminal of the charged car battery. 
  • Connect the corresponding black clamp to the metal post on the negative terminal of the charged car battery.
  • Go back to the dead car battery and find a grounding piece of metal to attach the final black clamp. Do not attach the black clamp to the negative terminal on the dead car battery as this can cause electrical sparks and poses a safety hazard.
  • Some cars have a built-in grounding spot under the hood for this task. Read your owner’s manual for more details.

Tip: To make sure the cables are well connected, make sure the metal pieces on each clamp are touching the metal part of each battery terminal post.  4

Jump-Start the Car

person turning the key in the ignition of a car

  • Once the cables are connected, start the vehicle with the charged battery and let it run for a couple minutes.
  • Go to the car with the dead battery and turn the key until the engine fully starts. This may take a few moments while the dead battery pulls energy from the other vehicle.

5

Remove the Jumper Cables

person's hand removing jumper cables from a car battery

  • Leave both cars running.
  • Start with the car that has the dead car battery and remove the black clamp from its grounding spot. Set it on the ground nearby, making sure it does not touch anything else under the car hood.
  • Remove the red clamp from the positive terminal on the dead car battery. Set it on the ground next to the black clamp and make sure they don’t touch each other.
  • Move over to the car with the charged car battery and repeat the process.
  • Remove the black clamp from the negative terminal and set it on the ground nearby, making sure it does not touch anything else under the car hood.
  • Remove the red clamp from the positive terminal and set it on the ground.
  • Since all clamps have now been removed, you can roll up the jumper cables and put them away.

Knowing how to jump-start a car is essential and safety must always be a priority.

If you cant get one of the tool we mentioned before you can call or request a service to jump start car nearby with us call to 888-853-3521 call us we will be happy to help you sending a driver that can provide a service to jump start car less then 30 minutes eta.

When you car stop in the freeway or in the street and show a sign of battery light on dashboard that mean yo got low power but the most common reason of that is when car alternator is going back in that case if you call a service to jump start cars will no solved the problem you will ended needing a reliable tow truck service that can bring your car to the nearest mechanic place or you can call our Mobile Mechanic that can go there and change your alternator on spot

jump start car service

How to jump start Cars?

The safe way to jump start cars is having another car nearby but when the car is on parking garage or on the garage most jumping cables doesn’t reach the other car you will need a portable jump start

I try to jump start cars and i make short i damage something?

Yes, Car computer is the one that goes bad after all is the one that control our car system any short circuit make the computer read wrong from sensor and that will make failures or codes on it

Is safe jump start a car with a bad alternator?

if The alternator is bad you will need a tow service jump start cars only works when your battery is low on power but when alternator is bad car will slow down the batter fast de to sparkplugs

How Much does a jump start cars Services cost?

Price fee may start from $50-$120 depending Distance you are, car model and time you call most services cost less on daytime time night time jump start cars services or any tow service cost more

What do i do if after jump start cars service does start my car?

In that case mean you got bad computer or fuel pump stop working or mechanical problem